3m interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? metpak ? 2-fb inverse header 2 mm 5-row, right angle, solder tail mp2 series physical electrical environmental metpak is a trademark of 3m company. futurebus+ is a registered trademark of the institute of electrical and electronic engineers, inc. (ieee) insulation material: high temp lcp flammability: ul 94v-0 color: beige contact material: copper alloy plating underplating: 50 " [1.27 m] nickel wiping area: see ordering information solder tails: see ordering information current rating: signal: 1.5 a - all contacts simultaneously insulation resistance: 10 3 m withstanding voltage: 1000 v ac temperature rating: -55 c to +125 c process temperature rating: 260c (profile per j-std-020c) moisture sensitivity level: 1 (per j-std-020c) ts-1122-04 sheet 1 of 4 date modified: march 28, 2007 ? three levels of early mate, late break (emlb) sequencing or selective loading options ? footprint compatible with standard futurebus+ ? ? solder tail with true-position wafer ? ideal for hot swapping applications ? end-to-end stackable ? right angle male for daughter card ? mates with mp2-r for backplane applications and mp2-sxxxg for coplanar applications ? see regulatory informati on appendix (ria) for chemical compliance information ul file no: e68080
3m interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? metpak ? 2-fb inverse header 2 mm 5-row, right angle, solder tail mp2 series ts-1122-04 sheet 2 of 4 mp2 - pxxx - 5xm1 - xxxxx ordering information p = right angle header inversed rows 5 = 5 rows loading pattern and tail length (see table 2) termination style m = solder tail 1.50 .059 17.80 .701 2.00 .079 4x mating length 7.00 .276 16.80 .662 3.86 .152 4.00 .157 8.00 .315 2.00 .079 4x 13.90 .547 3.75 .148 tail length "b" 2.00 .079 typ. mated with mp2-rxxx-5xxx-xxxx "a" 2.00 .079 typ. 13.00 .512 17.00 .669 row position x position 2 position 1 c d e a b pin count (see table 1) plating options: (seetable 3) 0 0.0 0.00 mm 3 0.3 0.13 mm [inch] tolerance unless noted [ ] dimensions for reference only note: 1. refer to iec 61076-4-104 futurebus+? global standard. 2. for special pin arrangements, contact 3m.
3m interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 3m ? metpak ? 2-fb inverse header 2 mm 5-row, right angle, solder tail mp2 series ts-1122-04 sheet 3 of 4 plating suffix plating composition plating suffix plating composition 0.25 m [10 "] min. au contact area 0.25 m [10 "] min. au contact area 2.54 m [100 "] min. snpb tail area 5.08 m [200 "] min. matt whisker mitigating sn tail area 1.27 m [50 "] min. ni all over 1.27 m [50 "] min. ni all over 0.76 m [30 "] min. au contact area 0.76 m [30 "] min. au contact area 2.54 m [100 "] min. snpb tail area 5.08 m [200 "] min. matt whisker mitigating sn tail area 1.27 m [50 "] min. ni all over 1.27 m [50 "] min. ni all over 0.08 m [3 "] min. au contact area 1.27 m [50 "] min. au contact area, lubricated 0.67 m [27 "] min. pdni contact area 5.08 m [200 "] min. matt whisker mitigating sn tail area 2.54 m [100 "] min. snpb tail area 1.27 m [50 "] min. ni all over 1.27 m [50 "] min. ni all over 0.08 m [3 "] min. au contact area 0.13 m [5 "] min. hard au contact area, lubricated 0.67 m [27 "] min. pdni contact area 1.02 m [40 "] min. pdni contact area 5.08 m [200 "] min. matt whisker mitigating sn tail area 0.10 m [4 "] min. pd contact area 1.27 m [50 "] min. ni all over 2.54 m [100 "] min. snpb tail area 0.13 m [5 "] min. hard au contact area, lubricated 1.27 m [50 "] min. ni all over 1.02 m [40 "] min. pdni contact area 0.10 m [4 "] min. pd contact area 5.08 m [200 "] min. matt whisker mitigating sn tail area 1.27 m [50 "] min. ni all over tr40b (ria e3 & c2 apply) lr (ria e1 & c1 apply) pd (ria e1 & c1 apply) fj (ria e1 & c1 apply) kr (ria e1 & c1 apply) rf (ria e1 & c1 apply) table 3 - plating tg (ria e3 & c2 apply) tg30 (ria e3 & c2 apply) tr30 (ria e3 & c2 apply) pin count rows 030 11.95 [0.471] 10.00 [0.394] 5 060 23.95 [0.943] 22.00 [0.866] 5 090 35.95 [1.415] 34.00 [1.339] 5 120 47.95 [1.889] 46.00 [1.811] 5 150 59.95 [2.36] 58.00 [2.283] 5 180 71.95 [2.833] 70.00 [2.756] 5 210 83.95 [3.305] 82.00 [3.228] 5 240 95.95 [3.778] 94.00 [3.701] 5 270 107.95 [4.251] 106.00 [4.173] 5 300 119.95 [4.722] 118.00 [4.646] 5 420 167.95 [6.612] 166.00 [6.535] 5 table 1 - connector & row lengths dim. "a" mm [inch] dim "b" mm [inch] loading pattern description mate length row a mate length row b mate length row c mate length row d mate length row e tail length row a tail length row b tail length row c tail length row d tail length row e 1 all positions filled 5.00 5.00 5.00 5.00 5.00 3.30 3.30 3.30 3.30 3.30 2 all positions filled 4.25 5.00 5.00 5.00 5.00 4.05 3.30 3.30 3.30 3.30 3 all positions filled 3.50 4.25 4.25 5.00 5.00 4.80 4.05 4.05 3.30 3.30 4 all positions filled 4.25 5.00 4.25 4.25 4.25 4.05 3.30 4.05 4.05 4.05 5 rows a, b, c, and d filled 5.00 5.00 5.00 5.00 na 3.30 3.30 3.30 3.30 na 6 rows a, b, c, and d filled 5.00 4.25 4.25 5.00 na 3.30 4.05 4.05 3.30 na 7 all positions filled 4.25 5.00 4.25 5.00 4.25 4.05 3.30 4.05 3.30 4.05 8 all positions filled 4.25 4.25 4.25 4.25 4.25 4.05 4.05 4.05 4.05 4.05 9 all positions filled 5.00 3.50 3.50 3.50 4.25 3.30 4.80 4.80 4.80 4.05 a all positions filled 3.75 4.50 5.25 4.50 3.75 4.55 3.80 3.05 3.80 4.55 b all positions filled 3.75 4.50 3.75 4.50 3.75 4.55 3.80 4.55 3.80 4.55 c all positions filled 5.75 5.75 5.75 5.75 5.75 2.55 2.55 2.55 2.55 2.55 d all positions filled 4.25 5.00 5.75 5.00 4.25 4.05. 3.30 2.55 3.30 4.05 f all positions filled 5.00 5.75 5.75 5.75 5.00 4.05 4.05 4.05 4.05 4.05 g rows a, b, c, and d filled 5.00 4.25 4.25 5.00 na 3.30 4.05 4.05 3.30 na table 2 - mate & tail lengths, mm vs. loading pattern
3m interconnect solutions http://www.3m.com/interconnects/ 3m is a trademark of 3m company. for technical, sales or ordering information call 800-225-5373 i n c l i n a t i o n t o l e r a n c e s 1.25 .049 initial offset allowable 1.00 .039 initial offset allowable 1.5 1 3m ? metpak ? 2-fb inverse header 2 mm 5-row, right angle, solder tail mp2 series ts-1122-04 sheet 4 of 4 recommended pcb hole mounting pattern 4.00 .157 "b" 2.00 .079 typ. 2.00 .079 4x 8.00 .315 4.00 .157 1.00 .039 12.00 .472 "d" plated thru hole o 2.05 +.05 -.00 .081 +.002 -.000 typ. unplated thru hole o 1.50 +.10 -.00 .059 +.004 -.000 typ. unplated thru hole 3.00 .118 lo .10 lo .10 lo .10 a1 hole finished dia. mm [in] cu thickness mm [in] snpb thickness microns ["] drilled hole dia. mm [in] "d" 0.65-0.80 [.0256-.0315] 0.025 [.001] min 15 [600] max 0.81-0.86 [.0319-.0339] table 4 -- hole plating for tg, tg30, tr30, tr40b finishes only hole finished dia. mm [in] cu thickness mm [in] immersion matte sn thickness microns ["] electrolitic au thickness microns ["] osp entek thickness microns ["] drilled hole dia. mm [in] 0.700-0.800 0.025-0.045 0.5 - 2.5 0.1 - 0.5 0.2 - 0.5 0.830-0.860 [.0330-.0340] or [.0276-.0315] [0.001-0.002] [20 - 100] [4 - 20] [8 - 20] 0.85mm [ #66] twist drill table 5 -- hole plating for fj, kr, rf, lr, and pd finishes only "d"
regulatory information appendix 3m electronic solutions division/interconnect europe appendix e1: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product is rohs compliant 2005/95/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e2: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under eu commission decision 2005/747/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e3: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment as amended by commission decision 2005/618/ec. this product contains lead in the solder tail area in excess of the maximum concentration value allowed. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix e4: european union rohs directive 2002/95/ec, restriction of the use of certain hazardous substances in electrical & electronic equipment, as amended by eu commission decision 2005/618/ec. this product contains decabde in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under eu commission decision 2005/17/ec. rohs compliant 2005/95/ec means that the product or part (product) does not contain any of the substances in excess of the maximum concentration values in eu directive 2002/95/ec, as amended by commission decision 2005/618/ec, unless the substance is in an application that is exempt under eu rohs. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. ria-2217-a
china appendix c1: china rohs electronic industry standard of the peoples republic of china, sj/t11363-2006, requirements for concentration limits for certain hazardous substances in electronic information products. this symbol, per marking for the control of pollution caused by electronic information products, sj/t11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the warranty stated below. appendix c2: china rohs 2 0 electronic industry standard of the peoples republic of china, sj/t11363-2006, requirements for concentration limits for certain hazardous substances in electronic information products. this symbol, per marking for the control of pollution caused by electronic information products, sj/t11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. unless otherwise stated by 3m in writing, this information represents 3ms best knowledge and belief based upon information provided by third party suppliers to 3m. the numerical reference in the symbol above should not be construed as a representation regarding the products life or an extension of a product warranty. the product warranty is stated below. in the event any product is proven not to conform with 3ms regulatory information appendix, then 3ms entire liability and buyers exclusive remedy will be in accordance with the product warranty stated below. important notice all statements, technical information, and recommendations related to 3ms products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. before using this product, you must evaluate it and determine if it is suitable for your intended application. you assume all risks and liability associated with such use. any statements related to the product which are not contained in 3ms current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3m. warranty; limited remedy; limited liability. this product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. 3m makes no other warranties including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. if this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3ms option, to replace or repair the 3m product or refund the purchase price of the 3m product. except where prohibited by law, 3m will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3m product, regardless of the legal theory asserted. name and content of hazardous substances or elements 3 electronic solutions division 6801 river place blvd. austin, tx 78726-9000 800/225-5373 www.3m.com/interconnects ria-2217-a ? 3m 2007
|
